Free Fortinet NSE 7 – Network Security 7.2 Support Engineer Exam NSE7_NST-7.2 Exam Practice Test

Which three common FortiGate-to-collector-agent connectivity issues can you identify using the FSSO real-time debug? (Choose three.)

• Refused connection. Potential mismatch of TCP port.
• Mismatched pre-shared password.
• Inability to reach IP address of the collector agent.
• Log is full on the collector agent.
• Incompatible collector agent software version.

Which two statements about conserve mode are true? (Choose two.)

• FortiGate starts dropping all new sessions when the system memory reaches the configured red threshold.
• FortiGate starts taking the configured action for new sessions requiring content inspection when the system memory reaches the configured red threshold.
• FortiGate enters conserve mode when the system memory reaches the configured extreme threshold.
• FortiGate exits conserve mode when the system memory goes below the configured green threshold

Which of the following regarding protocol states is true?

• proto_state=00 indicates that UDP traffic flows in both directions.
• proto_state-01 indicates an established TCP session.
• proto_state=10 indicates an established TCP session.
• proto state=01 indicates one-way ICMP traffic.

Refer to the exhibit, which shows the output of diagnose sys session stat. Which statement about the output shown in the exhibit is correct?

• AII the sessions in the session table are TCP sessions.
• 162 sessions have been deleted because of memory page exhaustion.
• There are 166 TCP sessions waiting to complete the three-way handshake.
• There are two sessions that have not been removed in case of any out-of-order packets that arrive.

Which two statements about application-layer test commands ate true? (Choose two.)

• Some of them display statistics and configuration information about a feature or process.
• Some of them display real-time application debugs.
• Some of them display only output, after you run the diagnose debug console enable command.
• Some of them can be used to restart an application.

Consider the scenario where the server name indication (SNI) does not match either the common name (CN) or any of the subject alternative names (SAN) in the server certificate. Which action will FortiGate take when using the default settings for SSL certificate inspection?

• FortiGate closes the connection because this represents an invalid SSL/TLS configuration
• FortiGate uses the 31 information from the Subject field in the server certificate.
• FortiGate uses the first entry listed in the SAN field in the server certificate.
• FortiGate uses the SNI from the user's web browser.

Which two conditions would prevent a static route from being added to the routing table? (Choose two.)

• The next-hop IP address is unreachable.
• The interface specified in the route configuration is down
• The route has a lower priority value than another route to the same destination.
• There is another other route to the same destination, with a lower distance.

Which statement about IKE and IKE NAT-T is true?

• IKE is used to encapsulate ESP traffic in some situations, and IKE NAT-T is used only when the local FortiGate is using NAT on the IPsec interface.
• IKE is the standard implementation for IKEv1 and IKE NAT-T is an extension added in IKEv2.
• They each use their own IP protocol number.
• They both use UDP as their transport protocol and the port number is configurable.

Which exchange lakes care of DoS protection in IKEv2?

• IKE_Req_INIT
• IKE_SA_INIT
• IKE_Auth
• Create_CHILD_SA

What are two functions of automation stitches? (Choose two.)

• You can configure automation stitches on any FortiGate device in a Security Fabric environment.
• You can create automation stitches to run diagnostic commands and attach the results to an email message when CPU or memory usage exceeds specified thresholds.
• An automation stitch configured to execute actions sequentially can take parameters from previous actions as input for the current action.
• You can set an automation stitch configured to execute actions in parallel to insert a specific delay between actions.