Free NetApp certified support engineer – ONTAP specialist Exam NS0-593 Exam Practice Test

You Just used the CLI to create a NetApp ONTAP FlexGroup Volume on a NetApp Cloud Volumes ONTAP instance. After creation, you notice odd behavior in NetApp Cloud Manager.In this scenario, what Is the reason for this behavior?

• Cloud Volumes ONTAP does not support FlexGroup volumes.
• The Capacity Management Mode within Cloud Manager should be set to Manual.
• The Capacity Management Mode within Cloud Manager should be set to Automatic.
• Cloud Manager must be used to provision the FlexGroup volume.

Referring to the exhibit, from which delay center is most of the latency for voll?

• Disk
• Network
• Data
• NVRAM

A customer's storage administrator Informs you about the deactivated Automatic Switchover (AUSO) feature on their MetroCluster IP environment.What Information would you tell your customer in this scenario?

• The AUSO feature cannot be activated due to a non-mirrored aggregate.
• The AUSO feature is not available in Metrocluster IP installations by design.
• A faulty link automatically deactivated the AUSO feature.
• This is a configuration failure, you can activate that feature for the customer.

You notice poor performance on your FlexGroup and execute the system node run -node * flexgroup show command for more Information. You notice the 'Urge' column has non-zero values.In this scenario, which statement is true?

• The aggregate is completely full.
• The constituent volumes are out of Inodes.
• The data placement is uneven.
• The constituent volumes are completely full.

Your customer has deployed a two petabyte NetApp ONTAP FlexGroup volume across their 4-node ONIAP 9.8 cluster. They plan to store over three billion files. They want to prevent file 10 conflicts since files are placed into the FlexGroup volume.In this scenario, which two NFS SVM parameters should be enabled? (Choose two.)

• -v3-64bit-identifiers
• -v4-fsid-change
• -v3-fsid-change
• -v4-64bit-idantifiers

You are attempting to connect a NetApp ONTAP cluster to a very complex network that requires LIFs to fail over across subnets.How would you accomplish this task?

• Configure an equal number of UFs on each subnet.
• Configure VIP LIFs using OSPF.
• Configure VIP LIFs using BGP.
• Configure a I IF failover policy for each subnet inside a single broadcast domain.

Your customer noticed in NetApp Active IQ that their NetApp Cloud Volumes ONTAP for Azure HA solution is no longer sending AutoSupport messages over HTTPS. A support ticket has been opened to find out why. No changes have been made to the Cloud Volumes ONTAP for Azure HA environment.In this scenario, which two autosupport command parameters should be used to validate that AutoSupport Is working properly? {Choose two.)

• -mail-hosts
• -transport
• -proxy-url
• -to

When you review performance data for a NetApp ONTAP cluster node, there are back-to-back (B2B) type consistency points (CPs) found occurring on the loot aggregate.In this scenario, how will performance of the client operations on the data aggregates be affected?

• During B2B processing, clients will be unable to write data.
• Data aggregates will not be affected by B2B processing on another aggregate.
• During B2B processing, all I/O to the node is stopped.
• During B2B processing, clients will be unable to read data.

You have connection Issues from a Linux host to an AFF A400 FC LUN. You are asked by support to run the NetApp sanlun command to provide troubleshooting information.Which NetApp software package must be installed on the host?

• Virtual Storage Console
• Inventory Collect Tool
• Host Utilities package
• SnapDrive for UNIX

Referring to the exhibit, what do you need to do to return the MetroCluster to a normal state?

• Enter the metroclustor switchback command on Site B.
• Enter the metrocluster switchback command on Site A.
• Enter the storage failover giveback command on Site B.
• Enter the storage failover giveback command on Site A.