Free NetApp Certified Storage Installation Engineer, ONTAP Exam NS0-184 Exam Practice Test

You completed a 2-node AFF A700 installation according to the poster. You run the disk show -fields owner command and notice that all drives are assigned to node 1.In this scenario, which tool would you use to access documentation and guidelines to solve the issue?

• Active IQ Unified Manager
• Active IQ One Collect
• NET2
• NetAppDocs

Your customer currently has a 4-node AFF A400 cluster that runs ONTAP 9.8, with two NS224 shelves that are connected to each HA pair. The customer needs to add additional capacity to the cluster.Which two actions would enable the customer to accomplish this task? (Choose two.)

• Connect the new NS224 shelves to the existing NS224 shelves and adjust the shelf IDs.
• Connect the new NS224 shelves to the existing Cisco Nexus 3232C switches.
• Deploy a new AFF A400 to the cluster.
• Deploy new, dedicated, storage switches for the new NS224 shelves.

An administrator issued the cluster setup command and configured a 2-node ONTAP 9.8 cluster.In this scenario, which tool would the administrator use to validate the configuration?

• Active IQ Upgrade Advisor
• Interoperability Matrix Tool
• NetAppDocs
• Active IQ Config Advisor

You are preparing for the installation of a new 2-node switchless AFF A250 ONTAP 9.8 cluster and need to obtain the preinstallation information from the customer.In this scenario, what are three examples of data required from the customer? (Choose three.)

• management IP addresses
• cluster switch name
• gateway IP address
• BMC IP addresses
• cluster name

Which command would be used to measure the throughput and latency of traffic between nodes?

• qos statistics workload performance show
• cluster ping-cluster
• network test-path
• statistics node show

You have added two new AFF A250 nodes to an existing 4-node cluster with NetApp CN1610 cluster network switches. Although the nodes can join the cluster, the storage failover show command output shows that the NVRAM log is not synchronized, and it cannot reach the partner over an HA interconnect.In this scenario, which two statements are true? (Choose two.)

• The AFF A250 requires switches with 40GbE port support.
• The AFF A250 uses different ports for the cluster and the HA interconnect.
• The AFF A250 requires switches with 25GbE port support.
• The AFF A250 uses the same port for the cluster and the HA interconnect.

On which type of network interfaces are the cluster interconnect LIFs created?

• on an FC or FCoE port
• on an interface group
• on a UTA port shared with other LIFs
• on a physical port

You are preparing to add a 2-node AFF A250 system to an existing 4-node AFF A800 cluster with Cisco Nexus 3232C switches. The cluster switches are currently running the Cluster-HA RCF.In this scenario, which two steps are required to install the AFF A250 system? (Choose two.)

• Load the Storage RCF.
• Cable the AFF A250 nodes to the next free ports on the switch.
• Cable the AFF A250 nodes to the breakout ports on the switch.
• Load the Cluster-HA-Breakout RCF.

A customer is asked to install a new AFF ASA A700 system. During the installation, the customer asks if ONTAP 9.8 is supported with their host's OS version running Windows 2016.In this scenario, which NetApp tool would verify supportability?

• ONTAP System Manager
• Active IQ Unified Manager
• Active IQ OneCollect
• Interoperability Matrix Tool

After the installation of a new ONTAP 9.8 cluster, you have to verify if AutoSupport works.In this scenario, which two commands would you use to accomplish this task? (Choose two.)

• system node autosupport history show
• system node autosupport check show
• system node autosupport destination show
• system node autosupport invoke