Free Aruba Certified Campus Access Mobility Expert Written Exam HPE7-A07 Exam Practice Test

An ACME company employee complained about a recent poor-quality VoIP call while moving around their office environment HPE Aruba Networking Central reported a fair UCC score for this call while your VoIP engineer reported that their systems reported a MOS of 2, 3. The VoIP devices are operating over the 5GHz frequency band.What are the possible contributing factors? (Select two.)

• Coverage AP deployment plans generally don't support enough cell overlap for VoIP.
• 802.tr is enabled in the WLAN Security settings.
• There was localized interference at the caller’s location
• 802.1K is disabled in the WLAN Security settings
• The client roamed into an area that continuously operates Zigbee.

What directly affects the MCS used by wireless stations? (Select two.)

• SNR
• retry rate
• channel utilization
• number of connected clients
• frequency band

An OSPF router has learned a pain 10 an external network by Doth an E1 and an E2 advertisement Both routes have the same path cost Which path will the router prefer?

• The router will prefer the E1 path.
• The router will use Doth paths equally utilizing ECMP.
• The router will prefer the E2 path.
• Both routes will be suppressed until the path conflict has been resolved.

A customer has deployed an AOS 10 mobility gateway cluster consisting of three controllers at a single site The WLAN is configured to tunnel wireless device traffic to the AOS 10 mobility cluster The clients are authenticated by ClearPass using WPA3-Enterprise (opmode wpa3-aes-ccm-128). The security team has requested the ability to force a wireless device to reauthenticate using ClearPass. Which steps are required to ensure ClearPass can consistently initiate a change of authorization against an AOS 10 mobility cluster, including during gateway failover scenarios? (Select two)

• set cluster mode to Auto Site under High Availability - Cluster configuration
• modify WLAN - SSID - VLAN - Mode Configuration
• enable manual cluster configuration under High Availability - Cluster Configuration
• enable Dynamic Authorization CoA under High Availability - Cluster Configuration
• modify NAS IPv4 address under Security - Advanced - RADIUS Client

You are troubleshooting a WLAN deployment with APs and gateways set up with an 802.1X tunneled SSIO. End-users are complaining that they can’t connect to die enterprise SSID. Which possible AP tunnel states could be the cause of the Issue? (Select two.)

• SM_STATE_RE KEYING
• SM_STATE_SURVIVED
• SM_STATE_CONNECTED
• SM_STATE_SURVIVING
• SM_STATE_CONNECTING

A customer’s infrastructure is set up to use both primary and secondary gateway clusters on the SSID profile based on best practices What is a valid cause tor having an equal spirt in APs connected to the primary and secondary gateway clusters?

• The secondary gateway cluster is heterogeneous
• The secondary gateway cluster is homogeneous
• The primary gateway cluster is up. out some APs are unable to reach the primary gateway cluster. These APs would connect to the secondary gateway cluster
• The primary gateway cluster is up. out some APs cannot reach the secondary gateway cluster. These APs would connect to the secondary gateway cluster

Which command would allow you to verity receipt of a CoA message on an AOS 10 GW?

• packet-capture datapath udp 3799
• packet-capture controipath udp 3799
• packet-capture interprocess udp 3799
• tcpdump host-port 3799

A customer has interfering devices that are seen over the air. They contact you and ask you to configure RAPIDS to help identify interfering and rogue APs. HPE Aruba Networking Central identifies a rogue AP and displays the connected switch port.How can HPE Aruba Networking Central identify which switch port the AP is connected to?

• device profiting on the switch
• from the AP MAC address table
• from the switch LLDP neighbors table
• from the switch MAC address table

A network administrator wants to configure an 802 1X supplicant for a wireless network that includes the following:

• AES encryption
• EAP-MSCHAPv2-based user and machine authentication
• validation of server certificate in Microsoft Windows 10
• The network administrator creates a WLAN profile and selects the change connection settings option Then the network administrator changes the security type to Microsoft Protected EAP (PEAP) and enables user and machine authentication under Additional Settings.
• What must the network administrator do next to accomplish the task?
• Enable user authentication
• Change the security type to Microsoft: Smart Card or other certificate.
• Change default RC4 encryption for AES
• Enable server certificate validation

An AOS 10 multi-site deployment has sites with AP-only bridged SSlDs and other sites with APs and gateways operating tunneled SSiDs. Client session state sync errors exist between secure lab environments and public -facing areas at several sites.What is causing the issues?

• The DTLS connections are down between APs in the lab and APs in public areas
• The affected clients are associated with an SSID with 11r and 11k disabled.
• The sites with issues are the overlay AP with gateway sites because the connection to HPE Aruba Networking central is interrupted
• The sites with issues are the AP-only deployments because the connection to HPE Aruba Networking Central is interrupted