Free Aruba Certified Campus Access Professional Exam HPE7-A01 Exam Practice Test

What is an Aruba-recommended best practice for hardening that only applies to Aruba CX 6300 series switches with dedicated management ports?

• Implement a control plane ACL to limit access to approved IPs and/or subnets
• Manually enable Enhanced Security Mode from a console session.
• Disable all management services on the default VRF.
• Create a dedicated management VRF, and assign the management port to it.

With the Aruba CX switch configuration, what is the first-hop protocol feature that is used for VSX L3 gateway as per Aruba recommendation?

• Active Gateway
• Active-Active VRRP
• SVI with vsx-sync
• VRRP

The customer needs a network hardware refresh to replace an aging Aruba 5406R core switch pair using spanning tree configuration with Aruba CX 8360-32YC switches What is the benefit of VSX clustering with the new solution?

• stacked data-plane
• faster MSTP converge processing
• dual Aruba AP LAN port connectivity for PoE redundancy
• dual control plane provides better resiliency

What are the requirements to ensure that WMM is working effectively'? (Select two)

• The APs and the controller are Wi-Fi CERTIFIED for WMM which is enabled
• All APs need to be from the AP-5xx series and AP-6xx series which are Wi-Fi CERTIFIED 6.
• The Client must be Wi-Fi CERTIFIED for WMM and configured for WMM marking.
• The Aruba AOS10 APs installed have to be converted to controlled mode
• The AP needs to be connected via a tagged VLAN to the wired port

You are doing tests in your lab and with the following equipment specificationsAP1 has a radio that generates a 10 dBm signalAP2 has a radio that generates a 11 dBm signalAP1 has an antenna with a gain of 9 dBiAP2 has an antenna with a gain of 12 dBi.The antenna cable for AP1 has a 2 dB lossThe antenna cable for AP2 has a 3 dB lossWhat would be the calculated Equivalent Isotropic Radiated Power (EIRP) for APT?

• 26 dBm
• 30 dBm
• 17 dBm
• -12 dBm

You are deploying a bonded 40 MHz wide channel What is the difference in the noise floor perceived by a client using this bonded channel as compared to an unbonded 20MHz wide channel?

• 2dB
• 3dB
• 8dB
• 4dB

With the Aruba CX 6000 24G switch with uplinks of 1/1/25 and what does the switch do when a client port detects a loop and the do-not-disabie parameter is used?

• Port status will be validated once status is cleared
• An event log message is created.
• The network analytics engine is triggered.
• Port status led blinks in amber with 100hz.

A customer is using a legacy application that communicates at layer-2. The customer would like to keep this application working to a remote site connected via layer-3 All legacy devices are connectedto a dedicated Aruba CX 6200 switch at each site.What technology on the Aruba CX 6200 could be used to meet this requirement?

• Inclusive Multicast Ethernet Tag (IMET)
• Ethernet over IP (EolP)
• Generic Routing Encapsulation (GRE)
• Static VXLAN

What does the 802.3bz standard describe?

• 2.5Gb and 5Gb Ethernet ports
• 60 W and 90W PoE
• AP directed roaming between APs
• 60 GHz P2P Wi-Fi

A customer has a site with 200 AP-515 access points 75AP-565 access points installed. The customer is rolling out new mobile phones with Wi-Fi-calling. 802.1X is in use for authenticationWhat should be enabled to ensure the best roaming experience?

• 802.1X
• 802. 11r
• 802.11W
• 802 .11h