Free Aruba Certified Edge Professional Exam HPE6-A75 Exam Practice Test

An administrator configures the MultiZone feature for a company network, where a mobility cluster is the primary zone and a standalone controller in the company's DMZ represents a secondary data zone. The administrator configures two AP Groups and respective VAPs for the zones on the Mobility Master (MM) in the primary zone. When the APs boot up and establish connections to both zones, the administrator notices that no data connections are established to the data zone.What must the administrator do to fix this problem?

• Configure the same AP Groups and VAPs on the standalone controller, and associate the MultiZone APs to both groups.
• Configure the same AP Group in the data zone as it is in the primary zone, and configure the VAPs in the data zone.
• Have the MultiZone APs initially boot from the standalone controller in the data zone.
• Create different AP groups and VAPs on the Mobility Master and standalone controllers, and associate the MultiZone APs to both groups.

What must an OSPF router do when it receives a link state update?

• It must participate in a new election for the Designated Router and Backup DR.
• It must initiate a graceful restart timer.
• It must re-establish adjacency with its Designated Router and Backup DR.
• It must run the shortest path first algorithm.

An administrator deploys an AP at a branch office. The branch office has a private WAN circuit that provides connectivity to a corporate office controller. An Ethernet port on the AP is connected to a network storage device that contains sensitive information. The administrator is concerned about sending this traffic in clear-text across the private WAN circuit.What can the administrator do to prevent this problem?

• Redirect the wired port traffic to an AP-to-controller GRE tunnel.
• Convert the campus AP into a RAP.
• Enable AP encryption for wired ports.
• Enable IPSec encryption on the AP's wired ports.

in a VPN that uses certificate-based authentication, which component must be configured on the Mobility Master (MM) to allow a RAP to successfully connect to a Mobility Controller (MC)

• RAP VPN username and password
• WLAN and new RAP group
• RAP IPSec pre-shared key
• RAP whitelist

When is it necessary to use an SNMP based Enforcement profile to send a VIAN?

• When we have to assign a vlan to a wired user on a third party wired switch that doesn't support RADIUS return attributes.
• When we have to assign a VLAN to a wired user on an Aruba Mobility Access Switch.
• When we have to assign a VIAN to a wired user on an Aruba Mobility Controller.
• When we have to assign a VLAN to a wired user on a third party wired switch that doesn't support RADIUS authentication.
• When we have to assign a VLAN to a wireless user on an Aruba Mobility Controller.

Which ArubaOS CLl command can an administrator execute to determine if AP load balancing is enabled in a cluster?

• show switches
• show lc-cluster group-membership
• show aaa cluster essid
• show ap active

A network administrator wants to use Aruba AirWave to audit an AOS-Switch configuration. What rs one requirement?

• The switch defines the AirWave IP address in its zero touch provisioning (ZTP) profile.
• The switch specifies the AirWave IP address for the RADIUS server used for Telnet and SSH authentication.
• The switch is authorized in AirWave, which has the correct credentials to log in as a CLI manager.
• The switch is set to Manage Read-Write mode in AirWave but is not set to Monitor Only + Firmware Updates.

An administrator wants to implement bandwidth limits for guest users to restrict their Internet usage. On the Mobility Master (MM), where would the administrator define these limits?

• User role
• Firewall policy
• AAA policy
• 802.1X policy

A company has AOS-Switches, Aruba ClearPass, and Aruba Airwave. A network administrator needs to set up a new switch with the same settings found on other switches in the company. Which action rs likely to be the most useful to perform the task?

• Access the Network Device view on ClearPass.
• Use the configuration audit tool on AirWave.
• View the current running config on each switch.
• View usage patterns on the switches on AirWave.

An administrator needs to authenticate users connected to an ArubaOS Switch where the switch authenticates the user, assigns the firewall policies to the user, and processes some of the users' traffic. Which connection method should the administrator configure on the ArubaOS-Switch?

• Per-user tunneled node
• Split-tunneled mode
• Per-port tunneled node
• VLAN tunneled mode