Free BIG-IP Administration Install, Initial Configuration, and Upgrade Exam F5CAB1 Exam Practice Test

An F5 VE has been deployed into a VMware environment via an OVF file.An administrator wants to configure the management IP address so the VE can be accessed for further setup.Which two are valid methods for configuring the management-ip address? (Choose two.)

• Log into the remote console and configure the management IP by running the config executable.
• Log into the remote console and configure the management IP through TMSH using: create sys management-ip /
• Log into the remote console and configure the management IP through TMSH using: create ltm management-ip /
• Log into the remote console and configure the management IP by running the setup command.

A secondary administrator has been granted access to a BIG-IP device through its Management Interface, but is unable to access the Configuration Utility (WebUI).What command can be run from the CLI to capture the network traffic on the management interface and troubleshoot the issue?(Choose two.)

• tcpdump -i eth0 -n port 443
• tcpdump -i mgmt -n port 443
• tcpdump -i 0.0 -n port 443
• tcpdump -i tun0 -n port 443
• tcpdump -i management -n port 443

What are the two options for securing a BIG-IP’s management interface? (Choose two.)

• Limiting network access through the management interface to a trusted/secured network VLAN.
• Block all management-interface administrative HTTPS and SSH service ports to prevent access.
• Use the BIG-IP’s Self-IP addresses for administrative access rather than the management interface.
• Restrict administrative HTTPS and SSH access to specific IP addresses or IP ranges.

The BIG-IP Administrator uses Secure Copy Protocol (SCP) to upload a TMOS image to the/shared/images/ directory in preparation for a TMOS upgrade.After the upload is completed, what will the system do before the image is shown in the GUI under: System » Software Management » Image List?

• The system verifies the internal checksum
• The system copies the image to /var/local/images/

A BIG-IP Administrator needs to install a HotFix on a standalone BIG-IP device, which has HD1.1 as the Active Boot Location.The administrator has already re-activated the license and created a UCS archive. In which sequence should the administrator perform the remaining steps?

• Install HotFix in HD1.2, Install base Image in HD1.2, Activate HD1.2
• Install HotFix in HD1.1, Reboot the BIG-IP device, Install UCS Archive
• Install base Image in HD1.2, Install HotFix in HD1.2, Activate HD1.2
• Activate HD1.2, Install base Image in HD1.2, Install HotFix in HD1.2

The BIG-IP Administrator needs to update access to the Configuration Utility to include the 172.28.31.0/24 and 172.28.65.0/24 networks.From the TMOS Shell (tmsh), which command should the BIG-IP Administrator use to complete this task?

• modify /sys httpd allow add { 172.28.31.0/255.255.255.0 172.28.65.0/255.255.255.0 }
• modify /sys httpd allow add { 172.28.31.0 172.28.65.0 }
• modify /sys httpd permit add { 172.28.31.0/255.255.255.0 172.28.65.0/255.255.255.0 }

A BIG-IP device will be dedicated to functioning as a WAF, requiring only the ASM module to be provisioned.What provisioning level will ensure that the system allocates all CPU, memory, and disk resources to this module exclusively?

• Dedicated
• Comprehensive
• Maximal
• Nominal

The BIG-IP Administrator uses Secure Copy Protocol (SCP) to upload a TMOS image to the/shared/images/ directory in preparation for an upgrade.After the upload is complete, what will the system do before the image appears in the GUI under: System » Software Management » Image List?

• The system performs a reboot into the new partition
• The system verifies the internal checksum
• The system copies the image to /var/local/images/

When using the tmsh shell of a BIG-IP system, which command will display the management-ip address?

• run /util bash ifconfig mgmt
• list /sys management-ip
• show /sys management-ip

An F5 BIG-IP Administrator is asked to report which modules are provisioned on the BIG-IP. In which two ways can this be done?(Choose two.)

• Via TMSH with show /sys provision
• Via the GUI at Statistics → Module Statistics → System
• Via TMSH with list /sys provision