Free Designing Cisco Data Center Infrastructure Exam 300-610 Exam Practice Test

An engineer must design a solution to divide the workload across two different data centers and achieve redundancy in case of the failure of either data center Which solution must the engineer choose?

• single Cisco HyperFlex stretched cluster
• Cisco Hyperflex edge cluster
• Cisco Hyperflex ROBO cluster
• single Cisco HyperFlex standard cluster

A network engineer must design a Cisco HyperFlex solution based on these requirements:* two clusters in the main data center consisting of five HyperFlex nodes* one edge node for the remote branch* cluster nodes that use one rack unit of spaceWhich two devices should be used in the remote branch cluster for this design? (Choose two.)

• Gigabit Ethernet Switch
• HX240C
• HX220C
• Fabric Interconnect 6300
• UCSB B200

Refer to the exhibit A Cisco engineer is configuring a next-generation Cisco HyperFlex HX data platform with 2 x Cisco UCS 6248UP fabric interconnects. 8 x Cisco HX-Series HX240c-M4SX servers, plus 8 x Cisco UCS B200-M4 blade servers Cisco UCS 5108 blade chassis, and Cisco UCS 2204XP fabric extenders The solution is configured with HX Release 4 5(2a) using VMware ESXi 7 0 U2 After the engineer migrates all customer VMs to the new solution platform, the engineer decides to create HX Native snapshots for all the VMs The engineer performs the operation and notices that some of the VMs are not creating snapshots. What is the most probable reason that the HX Native snapshots are not created?

• Virtual machines are in suspended state
• The servers have duplicate names
• The source disk is thick provisioned
• The node has insufficient datastore space

An engineer must design a Cisco UCS environment for a customer The design requires the most efficient use of available bandwidth with active-active uplinks The upstream Cisco Nexus 9000 Series Switch must automatically initiate the port-channel connectivity to the fabric interconnects Which configuration must the engineer choose to meet these requirements?

• * fabric interconnects in Ethernet switching mode * LACP port-channel from fabric interconnects and Cisco Nexus 9000 switches
• * fabric interconnects in Ethernet switching mode * static port-channel from fabric interconnects and Cisco Nexus 9000 switches
• * fabric interconnects in Ethernet end-host mode * LACP port-channel from fabric interconnects and Cisco Nexus 9000 switches
• * fabric interconnects in Ethernet end-host mode * static port-channel from fabric interconnects and Cisco Nexus 9000 switches

A network architect designs the iSCSI architecture. The requirements are to achieve high performance and a low amount of oversubscription and to minimize latency. Which two actions must be taken to meet these requirements? (Choose two.)

• Configure the size of the payload in each frame to MTU 9000.
• Minimize the number of hops between the storage and the hosts.
• Enable iSCSI port binding on the Initiator device.
• Set the size of the payload in each frame to MTU 1500.
• Use a software-based iSCSI adapter on the client side.

Which type of encoding is used on 8-Gbps links as compared to 10-Gbps links?

• 8-Gbps links use 64B/66B encoding, and 10-Gbps links use 8B/10B encoding.
• 8-Gbps links use 8B/10B encoding, and 10-Gbps links use 64B/66B encoding.
• 8-Gbps links and 10-Gbps links use 8B/10B encoding.
• 8-Gbps links and 10-Gbps links use 64B/66B encoding.

A network engineer must design a Cisco HyperFlex solution based on these requirements:* two clusters in the main data center consisting of five HyperFlex nodes* one edge node tor the remote branch* cluster nodes that use one rack unit of spaceWhich two devices should be used in the remote branch cluster for this design? (Choose two.)

• HX240c
• Fabric Interconnect 6300
• HX220c
• Gigabit Ethernet Switch
• UCS B200

What influences the number of ISLs that are required between Cisco MDS Series switches?

• FCoE protocol
• type of storage
• end-to-end oversubscription ratio
• N Port virtualization

A network administrator must create a redundant vHBA for the mission-critical virtual machines (VMs) installed on a Cisco UCS Fabric Interconnect blade server. The VMs access multiple datastores using VSAN55 and VSAN95. The datastore on which the VMs are hosted must be accessible if any of the uplinks goes offline. Which action meets these requirements?

• Attach VSAN55 to vHBA1 and VSAN95 to vHBA2.
• Assign VSAN55 and VSAN95 to vHBA1 and vHBA2.
• Enable failover for the vHBA with VSAN55 and VSAN95 enabled.
• Configure load-balancing for vHBAs with VSAN55 and VSAN95 attached.

An engineer must design Layer 2 connectivity for a subnet between two data centers. The engineer must ensure seamless host mobility and optimal first-hop routing. Which attribute must be synchronized across all data centers to achieve this goal?

• NX-OS version
• DCNM to manage both fabrics
• multicast group
• anycast gateway MAC